TB 9-2300-295-15/16
(17) Block 8. Enter the appropriate utilization code
(25) Block 14. Enter a
or an "X" in the space
p r o v i d e d to indicate when the failure was detected
from Table 1.
(table A-3). Leave blank if no failure is involved or
Table 1. Utilization Codes
when recording DA directed sampling items organi-
zational maintenance.
Description
Code
or an "X" in the space
(26) Block 15. Place a
Active Components (except as otherwise listed)
*ON
Depot Stock
1
p r o v i d e d that most accurately describes the condi-
Post supply activities
2
tions at time of first indication of trouble. For
(not used)
3
or "X" in the space provided and
"other," place a
*4
Operational readiness float (ORF)
enter the code number selected from table 4, appendix
Installation Maintenance and Service Equipment
5
(Not Used)
6
Army National Guard, except Mates
*7
recording DA directed sampling items organizational
Army National Guard (Mates)
*8
maintenance.
Air Force National guard units
9
(27) Block 16. E n t e r " W a r r a n t y C l a i m A c t i o n "
*A
Army Reserve units, except equipment pools
and give a complete description of the failure.
Army Reserve units, equipment pools
*B
(28) Block 16a. The unit owning the equipment
C
Air Force Reserve
Army ROTC
D
will enter their telephone number. This block will be
E
Air Force ROTC
used by support maintenance to record deferred
FORSCOM (all TOE units assigned direct FORSCOM)
F
maintenance, on-site maintenance, if applicable and
Defense Atomic Support Agency
G
t o record start and stop dates for each NMCS and
*H
US Army Intelligence and Security Command
NMCM days.
Defense Communications Security Agency
J
*K
US Army Training and Doctrine Command
(29) Block 23. Enter the authorization signature
L
US Army Test and Evaluation Command
and the Julian date in this block. Check your local
M
Labor service units
SOP.
*N
Prepositioned stock
Depot installation equipment
ing the work will verify the correctness of entries of
Equipment assigned to service schools and training
*Q
centers
R
Military Assistance Program (MAP)
indicated in (17a) through (28) below.
s
Overhaul facility, military
(1) B l o c k 1 7 a . E n t e r t h e d e s i g n a t i o n o f t h e
T
Overhaul facility, commercial
o r g a n i z a t i o n or activity accomplishing the work.
Manufacturing facility
u
(2) Block 17b. Enter the location of the organiza-
x
Repair Cycle Float (RCF)
t i o n or activity accomplishing the work.
*Denotee equipment utilization codes which require that
(3) Block 17c. Enter the unit identification code
separate Materiel Condition Status DA Form 2406, be submitted
by the activities and units required to report.
of the organization or activity accomplishing the
work. Commercial activities and contractors will
(18) Block 9. Enter the word "yes" or a "Y" if the
enter their manufacturer's code preceded by the let-
item is Materiel Condition Status Reportable, other-
t e r "K" as a substitute for the unit identification
wise leave blank.
code.
(19) Block 9a. Enter the Equipment Readiness
or an "X" in the appro-
(4) Block 18. Enter a
Code (ERC) if applicable.
priate block to indicate if the repairing organization
( 2 0 ) Block 9b. Enter the word "yes" or a "Y if
i s TOE, TD, or contractor operated.
the item is a pacing item.
(5) Block 19. E n t e r t h e a p p r o p r i a t e A r m y
(21) Block 10. Enter the hour reading (rounded
management system activity account code as defined
to the nearest hour) from the hour meter mounted on
in AR 37-100 series; if not applicable, leave blank.
t h e equipment listed in block 3. If not applicable,
(6) C o l u m n 2 0 a . E n t e r t h e a p p r o p r i a t e a c t i o n
leave blank.
c o d e , table A5, appendix A.
(22) Block 11. Enter the mileage reading (rounded
(7) Column 20b. Enter the appropriate failure
to the nearest mile) of the equipment listed in block
code.
3. If not applicable, leave blank.
(8) C o l u m n 2 0 c . E n t e r t h e n o m e n c l a t u r e o f
(23) Block 12. Enter total equivalent full charge
parts, components, assemblies, or other items
(EFC) rounds fired as recorded on DA Form 2408-4
replaced or on which work was performed; e.g.,
and DA Form 2408-10. If not applicable, leave
engine, track, etc. For compliance with technical
blank.
b u l l e t i n (TB) requirements, enter the TB number.
( 2 4 ) Block 13. F o r t u r b i n e e n g i n e s , e n t e r t h e
When additional space is required, use DA Form
number of hot starts. If not applicable, leave blank.
2407-1.
4-4
